A cabinet door that sits crooked can make an otherwise tidy kitchen, laundry or wardrobe look unfinished. The good news is that most modern concealed hinges are designed to be adjusted. Once you know which screw does what, you can adjust cabinet hinges to close evenly, line up the gaps and stop doors rubbing against each other.

The trick is to make small changes, one direction at a time. A quarter-turn can be enough. Start cranking every screw at once and it is easy to lose track of what has moved.

Before You Adjust Cabinet Hinges

Open the door and check that the cabinet itself is secure. If the carcase is loose, out of level or pulling away from the wall, hinge adjustment will only mask the real problem for a short time. This is especially relevant with flat-pack kitchens, tall pantry units and wardrobes, where a cabinet can shift if it has not been properly fixed to the wall or joined to the unit beside it.

Also check for obvious issues: loose screws, damaged hinge cups, swollen particleboard, a bent door or a shelf that is stopping the door from closing. Tighten any loose mounting screws first. If a screw just spins in the board, the fixing may be stripped and will need repair rather than further adjustment.

You will usually need only a Phillips-head screwdriver. Avoid a drill for fine hinge adjustments. It is too easy to over-tighten a screw or chew out the fitting, particularly on melamine or particleboard cabinets.

Know the Three Hinge Adjustments

Most concealed cabinet hinges give you movement in three directions: side to side, up and down, and in or out. The exact screw layout differs between brands, but the job follows the same principle.

Side-to-side adjustment

This is the adjustment used most often. It moves the door left or right so the gaps around it are even. On a double-door cabinet, it helps create a straight, consistent gap down the centre. On a single door, it stops the edge rubbing against the cabinet side.

Look for the adjustment screw on the hinge arm, usually the screw closer to the door. Turn it slowly and watch the edge of the door as you go. The direction varies by hinge, so do a small test turn rather than assuming clockwise will always move it the same way.

Aim for a neat, even reveal around the door. It does not need to be measured to the millimetre in every older home, as walls and cabinetry can be slightly out. What matters is that the door looks balanced, opens freely and does not touch the door beside it.

Height adjustment

If the top or bottom of the door is sitting too high, low or crooked against nearby doors, adjust the hinge mounting plate. This is the plate fixed to the inside wall of the cabinet.

On many hinges, you slightly loosen the two screws holding the mounting plate, move the door up or down, then tighten them again. Support the door while doing this, particularly if it is a heavy pantry, overhead cabinet or full-height wardrobe door. Adjust both hinges by the same amount where possible, then fine-tune if one corner still needs attention.

Height adjustment is often needed after a new kitchen has settled, after doors have been removed for painting or flooring work, or when a cabinet has been packed slightly differently during installation.

Depth adjustment

Depth adjustment moves the door closer to or farther from the cabinet. Use it when a door will not sit flush when closed, when it catches on an adjacent door, or when the gap at the front edge looks uneven from the side.

This screw is generally farther back on the hinge arm. A small turn changes how firmly the door meets the cabinet. Do not set it too tight. A door that is forced hard against the cabinet can bind, make noise and put unnecessary strain on the hinges.

A Simple Order That Saves Time

When several doors are out of line, work in a sensible order. Start with the cabinet that is clearly square and secure, then align the surrounding doors to it. For a bank of overhead cupboards or wardrobe doors, step back every few adjustments to check the whole run instead of focusing on one tiny gap.

First, set the height so the top and bottom edges line up. Next, use the side-to-side screws to create even gaps. Finish with the depth adjustment so the doors sit neatly against the cabinet face. Close each door gently after every small change. Slamming it shut can hide rubbing or binding that will show up later.

If a door has two hinges, make equal changes first. For example, if the whole door needs to move left, adjust both hinges in the same direction. If only the top corner is out, make a smaller correction to the top hinge. This keeps the door from twisting.

Common Problems and What They Usually Mean

A door that rubs along the top or bottom edge usually needs a height adjustment. If it catches along the side or clashes with another door, it is normally a side-to-side issue. A door that springs open slightly after closing may need the depth adjusted, although a shelf, drawer or internal fitting could also be obstructing it.

When the gap is wide at the top but tight at the bottom, the door is not necessarily the problem. It may be sitting at an angle because one hinge needs a different side adjustment. Work in very small turns and check the gap from top to bottom.

A door that drops again a few days after adjustment is a warning sign. The mounting screws may be loose, the screw holes may be damaged, or the door could be too heavy for the hinges fitted. Simply tightening the adjustment screw will not solve a failing fixing.

Soft-close hinges add another variable. If the door closes smoothly but stops short, check whether the soft-close mechanism is switched on or off correctly. Some hinges have a small clip or lever to adjust the closing action. If the mechanism is damaged, replacement is usually more practical than trying to force it back into shape.

When Hinge Adjustment Is Not the Real Fix

Not every crooked cabinet door can be fixed with a screwdriver. Water damage around a sink cabinet, for example, can swell the particleboard until hinge screws no longer hold. A warped door may never sit perfectly flat. Cabinets fixed on an uneven wall can also leave doors looking wrong even when their hinges are adjusted correctly.

The same applies when a kitchen or wardrobe has been assembled without proper levelling, wall fixing or cabinet-to-cabinet joining. You might be able to improve the appearance with hinge adjustments, but doors will continue to move if the installation underneath is not solid.

For large kitchen runs, tall wardrobes and new flat-pack installations, it can be quicker and safer to have the whole setup checked. The Box Busters handles cabinet assembly, secure fixing and door alignment across Melbourne and the South Eastern Suburbs, so the job is finished properly rather than patched up one hinge at a time.

Keep Doors Running Well

Once the doors are aligned, open and close every one of them a few times. Check that handles do not clash, drawers clear the doors, and soft-close mechanisms work as they should. Wipe away dust from the hinge area and avoid hanging heavy bags from handles, which can pull doors out of alignment over time.

A well-adjusted cabinet door should feel boring in the best possible way: it opens, closes and lines up without demanding another thought. If yours still fights you after a careful adjustment, the smart next step is to fix the cabinet or hinge problem behind it, not keep turning screws.